This blog is about sailing my home-build "Goat Island Skiff". A 16ft wooden "new classic" dinghy designed by Michael Storer.
I have started building this boat in September 2009 and launched it October 2010. I am using it mainly as a single-handed trailer-sailer dinghy in my home-area, the inland waterways of the Dutch "Biesbosch" and surrounding rivers.
donderdag 23 september 2010
For convenient rowing it's nice to have your oars fixed in the oarlocks at the right position.
I have made epoxy-glas reinforcements on these places to avoid wearing.
After that I applied some thickend epoxy and winded a piece of rope around it. I used some masking tape to fix this rope until the epoxy has cured.
When the epoxy is hard, the rope is well fixed and avoids sliding out of the oarlocks.
Today there was not much wind, but I was surprized how well GIS sailed with very little wind.
You have to keep your weight on the middle seat. You also have to keep a nice amount of heeling, that also helps to have the sail set quite well. Keep the tip of the boom well overboard and she is "speedy" with almost no wind at all. Under these superlight circumstances she still steers very well, you will have sufficient "feeling" about her balance and tuning. In this perspective it is one of the nicest boats I have ever sailed in these very light-wind conditions.
When the wind completely died I have rowed her a long way back. I have kept the rudder down and fixed the helm with a rope in the middle. I lifted the centerboard by about 30-40 cm and than she rows and tracks very well at reasonable speed.
I took my outboard with me for the first time. It's an older 2Hp 2stroke, weight 10kg. Plenty of power to have a GIS speed up very well. I used my rudder to steer and kept the centerboard down. It is nice that there is plenty of stability if you need to sit or kneel on the aft deck to handle the outboard. But keep your weight on the middle seat to maximize speed. It is nice to see that the hull hardly makes any waves and runs so smooth.
I think it's quite useless to buy and take an outboard on GIS in case there is no wind; GIS rows very well and you will get her anywhere rowing.
But an outboard gives more overall speed and could be helpfull if you need to go against waves and wind, when there is no space to tack or in busy harbours. I already had a small outboard, but I probably would not have spend money to buy one for my GIS.
One of the nice things of a flat-bottum skiff design is that it fits on any trailer.
I already had this 200x120 cm box-trailer and made it ready to carry my new boat. The overall weight of the boat is around 100kg so it is quite light-weight.
You see everything fits nice and compact inside the hull. I have made a cut-out in the transom for a small outboard and another one to hold the mast.
Getting the boat into the water on a trailer-ramp is quite easy; just lift the bow a bit and push it back. Gravity helps to slide the hull towards the water. If the back of the hull is afloat, you simply lower the bow into the water standing in the trailer-box.
To get the boat on the trailer takes a bit more effort. First step is to stand in the trailer-box and lift the bow onto the trailer. After that I attach a heavy 1:4 tackle ( old mainsheet system from a yacht ) on the bow ( strong eye-bolt ) and pull the hull forward untill it is in the right position.
If you handle things right, you do not even get your feet wet.
I have used holes to fix ropes in more occasions.
I drilled 12 mm holes to fix mooring lines. Just take a rope through a hole and use a stopper-knot to hold it in place.
I have also used holes to fix a rope-traveller. I have used 5 mm Dynema for this.
To have these holes nicely rounded helps to protect both epoxy and the rope itself.
dinsdag 21 september 2010
One of the main interesting things in the design of a Goat Island Skiff is simplicity! In my opinion KIS (Keep It Simple) is one of the main principles of succesfull boatdesign, sailing and yachting. You eliminate costs and maintenance and improve fun and safety.
Following this KIS principle I try to keep rigging as simple as possible. While building this GIS I have drilled 8mm holes around the mast area, rounded them as much as possible and soaked them with epoxy. Simple 4mm dynema rope-loops are used to fix anything needed. I have used 8mm stainless washers to avoid knots to enter these holes.
No screws, nothing that can be damaged, light weight, easy adaptable or removed, and at very little costs.
Last step in making non-slip area's.
After the varnish has cured you can start brushing loose sand and smaller stones off . Do not use a very soft brush, but also avoid to damage the fixed layer of sand.
Use a vacuum cleaner to remove things carefully.
The last step is a second layer of varnish on the sand to fix it.
This sand will soak up quite a lot of varnish, I have used some extra thinner to be able to spread it better. I also varnished the masked area's to have a smooth layer on both bottum panels.
It can take a few days before this last layer of varnished has fully cured.
This leaves a very functional semi-transparant non-slip area with great durability. If it appears to be too sharp, you can use a second layer of varnish.